StripFlock Pro

StripFlock® Pro Heat Transfer Vinyl

The only flock in the industry that can be layered on itself!

A great alternative to embroidery, StripFlock Pro heat transfer vinyl gives logos a raised, textured, suede-like feel. The fuzzy opaque colors make StripFlock Pro excellent for retro designs like you'd find in a mall in the 80's, or anytime you want a deep, rich look. StripFlock Pro is thick enough to cover hat seams, yet also looks excellent on bags, denim, and other garments that need textured visual interest. Use Stripflock Pro as a base layer and cover with other materials such as EasyWeed Stretch for an embossed look, or layer with more StripFlock! The ability to layer this material with itself and others allows you to say “yes” to multi-color designs. However, please note that for best results all fluorescent colors are recommended to be layered with the knockout method and the carrier peeled warm.

StripFlock Pro is 410 Microns / 16.1 mils and is a PVC composition.



StripFlock Pro Features

StripFlock Pro Shirt Design
StripFlock Pro White   StripFlock Pro Gray   StripFlock Pro Anthracite   StripFlock Pro Black   StripFlock Pro Brown   StripFlock Pro Burgundy   StripFlock Pro Red   StripFlock Pro Bright Red
StripFlock Pro Orange   StripFlock Pro Yellow   StripFlock Pro Lemon   StripFlock Pro Green   StripFlock Pro Pale Blue   StripFlock Pro Turquoise   StripFlock Pro Royal Blue   StripFlock Pro Navy Blue
StripFlock Pro Purple   StripFlock Pro Fuchsia   StripFlock Pro Light Pink   StripFlock Pro Fluorescent Red   StripFlock Pro Fluorescent Orange   StripFlock Pro Fluorescent Yellow   StripFlock Pro Fluorescent Green   StripFlock Pro Fluorescent Pink

StripFlock Pro fluorescent colors require a warm peel.

StripFlock Pro Applies to:




Craft Cutter Settings


    Cricut:
Blade: Standard    Setting: Iron-on+

    Silhouette Cameo:    
Blade:
Standard, 4    Material: Heat Transfer, Flocked    Speed:     Force:  6

    Brother ScanNCut:    
Blade:
Standard, 4    Cut Speed: 1    Cut Pressure: 2


Settings may vary based on blade condition and age of machine. Always perform a test cut prior to cutting designs.




Pro Cutter Settings


    Roland GX/GS-24:
Blade: 45°    Gram Force: 80-120    Offset: .250    Speed: 30 cm/s

    Graphtec:    
Blade:
45°    Force: 10    Tool: CB09+0    Speed: 30 cm/s

    MH, SC2, LP3, and Titan 1:    
Blade:
45°/60°    Gram Force: 100-110    Speed: 180 mm/s *Blade Advancing Varies

    Titan 2 & 3:    
Blade:
45°/60°    Gram Force: 100-110    Speed: 300 mm/s *Blade Advancing Varies

    Mimaki CG-60SR III:    
Blade:
45°    Gram Force: 110    Offset: 30    Speed: 20-30 cm/s


Settings may vary based on blade condition and age of machine. Always perform a test cut prior to cutting designs.




Application Instructions


Home Iron Instructions

• Set iron dial between Cotton and Linen
• Cover with Heat Transfer Cover Sheet or Multipurpose Paper
• Place on flat, hard surface (ironing board not recommended)
• Press iron with medium/firm pressure (do not slide iron)
• Press each section of design for 15 seconds
• If areas of design lift after application, replace cover sheet and
re-press for 10 seconds
• Peel carrier warm

Heat Press Instructions     

• Cover with Heat Transfer Cover Sheet or Multipurpose Paper
• Preheat garment for 2-3 seconds
• Apply design at 311°F/155°C
• Use medium pressure for 15 seconds
• Peel carrier warm (at least 10 seconds off press) 

Click here for a printable version of all HTV application instructions




Recommended Accessories:

Siser Weeder
Multipurpose Paper or
Heat Transfer Cover Sheet

Laundering:

Wait 24 hours before first wash
Machine wash warm or cold / mild detergent
Dry on normal dryer setting
Do not dry clean


StripFlock Pro Design